<?xml version="1.0" encoding="UTF-8"?>
<rss version="2.0"
	xmlns:content="http://purl.org/rss/1.0/modules/content/"
	xmlns:wfw="http://wellformedweb.org/CommentAPI/"
	xmlns:dc="http://purl.org/dc/elements/1.1/"
	xmlns:atom="http://www.w3.org/2005/Atom"
	xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
	xmlns:slash="http://purl.org/rss/1.0/modules/slash/"
	>

<channel>
	<title>Surface Production Facility &#187; Flotation Units</title>
	<atom:link href="http://www.process-facility.com/category/oil-handling-surfacefacilities/produced-water-treating-system/water-treating-equipment/flotation-units.html/feed" rel="self" type="application/rss+xml" />
	<link>http://www.process-facility.com</link>
	<description>Oil and Gas Production Facility Design</description>
	<lastBuildDate>Fri, 14 May 2010 03:34:57 +0000</lastBuildDate>
	<generator>http://wordpress.org/?v=abc</generator>
	<language>en</language>
	<sy:updatePeriod>hourly</sy:updatePeriod>
	<sy:updateFrequency>1</sy:updateFrequency>
			<item>
		<title>Sizing Dispersed Gas Units</title>
		<link>http://www.process-facility.com/sizing-dispersed-gas-units.html</link>
		<comments>http://www.process-facility.com/sizing-dispersed-gas-units.html#comments</comments>
		<pubDate>Sat, 05 Sep 2009 00:42:48 +0000</pubDate>
		<dc:creator>admin</dc:creator>
				<category><![CDATA[Flotation Units]]></category>
		<category><![CDATA[Dispersed Gas]]></category>
		<category><![CDATA[Sizing]]></category>

		<guid isPermaLink="false">http://www.process-facility.com/?p=558</guid>
		<description><![CDATA[




It can be shown mathematically that an efficient design must have a high gas induction rate, a small diameter induced gas bubble, and relatively large mixing zone. The design of the nozzle or rotor, and of the internal baffles, is thus critical to the unit&#8217;s efficiency.
As measured in actual field tests, these units operate on [...]]]></description>
		<wfw:commentRss>http://www.process-facility.com/sizing-dispersed-gas-units.html/feed</wfw:commentRss>
		<slash:comments>0</slash:comments>
		</item>
		<item>
		<title>Dispersed Gas Units</title>
		<link>http://www.process-facility.com/dispersed-gas-units.html</link>
		<comments>http://www.process-facility.com/dispersed-gas-units.html#comments</comments>
		<pubDate>Sat, 05 Sep 2009 00:07:04 +0000</pubDate>
		<dc:creator>admin</dc:creator>
				<category><![CDATA[Flotation Units]]></category>
		<category><![CDATA[Dispersed Gas Units]]></category>

		<guid isPermaLink="false">http://www.process-facility.com/?p=551</guid>
		<description><![CDATA[




In dispersed gas units gas bubbles are dispersed in the total stream either by the use of an inductor device or by a vortex set up by mechanical rotors. Figure 7-14 shows a schematic cross section of a unit that employs a hydraulic eductor. Clean water from the effluent is pumped to a recirculation header [...]]]></description>
		<wfw:commentRss>http://www.process-facility.com/dispersed-gas-units.html/feed</wfw:commentRss>
		<slash:comments>0</slash:comments>
		</item>
		<item>
		<title>Dissolved Gas Units</title>
		<link>http://www.process-facility.com/dissolved-gas-units.html</link>
		<comments>http://www.process-facility.com/dissolved-gas-units.html#comments</comments>
		<pubDate>Fri, 04 Sep 2009 23:55:34 +0000</pubDate>
		<dc:creator>admin</dc:creator>
				<category><![CDATA[Flotation Units]]></category>
		<category><![CDATA[Dissolved Gas Units]]></category>

		<guid isPermaLink="false">http://www.process-facility.com/?p=546</guid>
		<description><![CDATA[




Dissolved gas designs take a portion of the treated water effluent and saturate the water with natural gas in a contactor. The higher the pressure the more gas can be dissolved in the water. Most units are designed for a 20 to 40 psig contact pressure. Normally, 20% to 50% of the treated water is [...]]]></description>
		<wfw:commentRss>http://www.process-facility.com/dissolved-gas-units.html/feed</wfw:commentRss>
		<slash:comments>0</slash:comments>
		</item>
	</channel>
</rss>
